鋁合金升降機的安全操作時保證工作正常完成和工作人員安全的重要因素，所以防止升降機脫軌運行是必須要處理好的問題之一。一種鋁合金升降機防脫軌裝置,包括安裝板和傳感器,安裝板固定在鋁合金升降機吊籠或驅動裝置上,傳感器固定在安裝板上,傳感器的感應端正對鋁合金升降機導軌架的金屬構件,在鋁合金升降機吊籠或驅動裝置的頂部設置有一個安裝板和傳感器,在鋁合金升降機吊籠的底部還設有一個安裝板和傳感器,該兩個傳感器的信號輸出線均與控制裝置相連,傳感器是接近開關。本實用新型在鋁合金升降機的最頂部和最底部都設有一個傳感器,該傳感器用于檢測其正前方的金屬物體,借此檢測鋁合金升降機是否還處在導軌范圍內,如果其中一個傳感器沒檢測到導軌,則有控制系統切斷鋁合金升降機電源,避免鋁合金升降機脫軌。

1、找準升降臺底座的水準儀并且是討價的中心線與立柱的中心線重合一直，然后把桿安裝在平臺的上方，穿好鋼絲繩，調整好軌柱的為止并固定。
Identify the base of the water level and the lift is bargaining centerline centerline coincides with the column has been, and then put the lever mounted above the platform, put the rope, adjust the column until good rail and fixed.

2、將把桿安裝于自升平臺上，穿好鋼絲繩。安裝第一組立柱，標準節放入套架內，與底座螺栓連接。調整立柱軌道面凈距控制在1985mm以內，垂直度偏差應在≤1.5‰。
Since the peace and prosperity will rod mounted on the stage, put the rope. Installation of the first set of columns, standard section into the socket frame connected to the base bolts. Adjust Ram orbital plane spacing control within 1985mm, vertical deviation should be ≤1.5 ‰.

3、將提升滑輪置于安裝好的兩立柱頂端，穿繞提升鋼絲繩。利用電動卷揚機提升自升平臺。將伸縮卡收回至卡牢位置，直到伸縮卡底部與立柱頂面第一格平齊，將伸縮卡板復位，放松提升鋼絲繩，取下提升滑輪置于平臺上。
The upgrade installed two pulleys placed on top of the column, to wear around the hoisting cable. The use of electric winch lifting jack platform. The expansion card back to the card firmly position until the bottom of the column stretching card top surface is flush with the first grid, the expansion card board reset, relax lifting rope, remove the lifting pulley placed on the platform.

4、把第三組的標準節放入提升欄桿內，設置好欄桿的高度，在相應的高度上安裝鋁合金升降機好停車支架，就可以投入試運行。
The standard section of the third group within the railing into the upgrade, set the height of good railings, aluminum lift the parking bracket installation on the appropriate height, you can put into trial operation.
 

升降機廠家：http://55506132.com/